wm

Electrolux Washing Machine Repair

 

EPL Appliance Repairs is a professional centre for repair and maintenance of all Electrolux Washing Machine including top loaders and front loaders. Our technicians fix and service all Electrolux Washing Machine models.

Electrolux Basic Washing Machine Error Codes

 
Error CodeError ShowesPossible ProblemHow to fit
Fault Code / Error Code E10 appears. The LCD display RINSE + flashes There is no water flows Water tap is closed. Open the water tap.
    Filter in screw connection of the inlet hose is blocked. Close the water tap. Unscrew the hose from the tap, remove the filter and clean under running water
    Water tap is blocked with limescale or is faulty Check the water tap and have it repaired if necessary.
      Replace the inlet valve inside the washing machine
The fault Code / Error Code E20 appears. The RINSE display flashes. The washing is not sufficiently spun. Water is left in the drum. Drain hose is kinked. Remove the kink.
    Maximum pump head (discharge height 1m from the appliance's base) is exceeded. Contact your local Service Force Centre. For pumping heights over 1m a conversion kit is available as a special accessory.
    Drain pump is blocked. Switch off the appliance and pull out the mains plug. Clean the drain pump
The fault Code / Error Code E40 appears. The display MAIN WASH flashes   The door is not correctly closed. Close the door correctly. Start the programme again.
       
       
       
      0
       
       
       
       
       
       
       
       
       
       
       
       
       
       
       
       
       
       
       
       
       
       
       
       
       
       
       
       

 

Electrolux Washing Machine Error Codes, EWFM series, AWF series:

 

 
Error CodeError ShowesPossible ProblemHow to fit
E10 The water tap is closed. Open the water tap. Call EPL Appliance Repairs 1300 EPL 000
  The inlet hose is squashed or kinked. Check the inlet hose connection. Call EPL Appliance Repairs 1300 375 000
  The filter in the inlet hose is blocked. Clean the water inlet hose filter. Call EPL Appliance Repairs 1300 EPL 000
E20 The drain hose is squashed or kinked. Check the drain hose connection. Call EPL Appliance Repairs 1300 375 000
  The drain filter is clogged. Clean the drain filter. Call EPL Appliance Repairs 1300 EPL 000
E40 The door has not been closed. Close the door firmly. Call EPL Appliance Repairs 1300 375 000
  The door is not properly closed Close firmly the door Call EPL Appliance Repairs 1300 EPL 000
       
 
 

Electrolux Washing Machine Error Codes ENV series 

 
 
Error CodeError ShowesPossible Problem
E11 Tap closed or water pressure too low; Drain tube improperly positioned; Water fill solenoid valve is faulty; Leaks from water circuit on pressure switch; Pressure switch faulty; Wiring faulty; PCB faulty. Cycle is paused with door locked.
E12 Tap closed or water pressure too low; Drain tube improperly positioned; Water fill solenoid valve is faulty; Leaks from water circuit on pressure switch; Pressure switch faulty; Wiring faulty; PCB faulty. Cycle is paused with door locked.
E13 Drain tube improperly positioned; Water pressure too low; Water fill solenoid valve is faulty; Water circuit on pressure switch is leaking/clogged; Pressure switch faulty. Cycle is paused with door locked.
E21 Drain tube kinked/clogged/improperly positioned; Drain filter clogged/dirty; Drain pump faulty; Pressure switch faulty; Wiring faulty; PCB faulty; Electrical current leak between heating element and ground. Cycle is paused (after 2 attempts).
E22 Drain tube kinked/clogged/improperly positioned; Drain filter clogged/dirty; Drain pump faulty; Pressure switch faulty; Wiring faulty; PCB faulty; Electrical current leak between heating element and ground. Cycle is paused
E23 Drain pump faulty; Wiring faulty; PCB faulty. Safety drain cycle - Cycle stops with door unlocked.
E24 PCB faulty. Safety drain cycle - Cycle stops with door unlocked.
E31 Pressure switch; Wiring; Main PCB. Cycle stops with door locked.
E32 Drain tube kinked/clogged/improperly positioned; Drain filter clogged/dirty; Drain pump faulty; Water circuit on pressure switch; pressure switch; Wiring; main board. Cycle is paused.
E35 Water fill solenoid valve is faulty; Leaks from water circuit on pressure switch; Pressure switch faulty; Wiring faulty; PCB faulty. Cycle stops. Safety drain cycle. Drain pump continues to operate (5 min. on, then 5 min. off, etc.).
E38 Water circuit on pressure switches; Pressure switches; Motor belt broken. Heating phase is skipped.
E3A PCB faulty. Cycle stops with door locked.
E41 Door lock unit faulty; Wiring faulty; PCB faulty. Cycle is paused.
E42 Door lock unit faulty; Wiring faulty; PCB faulty. Cycle is paused.
E43 Door lock unit faulty; Wiring faulty; PCB faulty. (Safety drain cycle) Cycle stops.
E44 PCB faulty. (Safety drain cycle) Cycle stops.
E45 PCB faulty. (Safety drain cycle) Cycle stops.
E51 PCB faulty; current leakage from motor or from wiring. Cycle blocked, door locked (after 5 attempts).
E52 Motor faulty; wiring faulty; PCB faulty. Cycle blocked, door locked (after 5 attempts).
E53 PCB faulty. Cycle blocked, door locked
E54 PCB faulty; current leakage from motor or from wiring Cycle blocked, door locked (after 5 attempts).
E57 Wiring defective on inverter for motor, inverter board defective. Cycle blocked, door locked (after 5 attempts).
E58 Wiring defective on inverter for motor, inverter board defective, abnormal motor operation (motor overloaded); Motor defective. Cycle blocked, door locked (after 5 attempts).
E59 Motor defective; Wiring defective on inverter for motor; Inverter board defective. Cycle blocked, door locked (after 5 attempts).
E5A Inverter board defective. NTC open (on the inverter board). Overheating caused by continuous operation or ambient conditions (let appliance cool down). Cycle blocked, door locked (after 5 attempts).
E5H Wiring defective, Inverter board defective. Cycle blocked, door locked (after 5 attempts).
E5C Inverter board defective, the masters voltage is too high (measure the masters voltage). Cycle blocked, door locked (after 5 attempts).
E5d Line interference, Wiring defective, defective main board or inverter board. Cycle blocked, door locked (after 5 attempts).
E5E Defective wiring between main board and inverter board, Defective inverter board, defective main board. Cycle stops
E5F Defective inverter board, Defective wiring, defective main board. Cycle stops with door locked (after 5 attempts).
E61 NTC sensor faulty; heating element faulty; wiring faulty; PCB faulty. The heating phase is skipped.
E62 NTC sensor faulty; heating element faulty; wiring faulty; PCB faulty. Safety drain cycle � Cycle stopped with door open.
E66 PCB faulty. Safety drain cycle � Cycle stopped with door open.
E68 Earth-leakage between heater and earth. Cycle blocked with door open.
E69 Washing heating element interrupted (thermofuse open)  
E71 Faulty NTC sensor; Wiring faulty; PCB faulty. Heating is skipped.
E72 Wiring faulty; Drying NTC sensor (condenser) faulty; PCB faulty. Drying heating is skipped
E73 Wiring faulty; Drying NTC sensor (duct) faulty; PCB faulty. Drying heating is skipped
E74 NTC sensor improperly positioned; Faulty NTC sensor; Wiring faulty; PCB faulty. Heating is skipped.
E82 PCB faulty (Wrong configuration data). Selector, wiring  
E83 PCB faulty (Wrong configuration data). Selector, wiring Cycle cancelled.
E91 Wiring faulty; Faulty control/display board PCB faulty.  
E92 Wrong control/display board; Wrong PCB (do not correspond to the model). Cycle interrupted.
E93 Incorrect configuration data; PCB faulty Cycle interrupted.
E94 Incorrect configuration data; PCB faulty. Cycle interrupted.
E95 PCB faulty. Cycle interrupted.
E97 Faulty PCB (Wrong configuration data). Cycle interrupted.
E98 Incompatibility between main board and Inverter. Cycle interrupted.
E9b / E9H Display board. Cycle interrupted.
E9C Display board. Cycle interrupted.
E9d Display board. Cycle interrupted.
E9F PCB. Cycle interrupted.
EH1 Power supply problems (incorrect / disturbance); PCB faulty. Wait for frequency nominal conditions.
EH2 Power supply problems (incorrect / disturbance); PCB faulty. Wait for voltage nominal conditions.
EH3 Power supply problems (incorrect / disturbance); PCB faulty. Wait for voltage nominal conditions.
EHE Wiring faulty; PCB faulty. Safety drain cycle � Cycle stopped with door open
EHF PCB faulty. Safety drain cycle � Cycle stopped with door open
EC1 Solenoid valve faulty/blocked; PCB faulty. Cycle interrupted with door closed. Drain pump functions always (5 min., then it stops for 5 min. etc.)
EC3 Wiring faulty; Weight sensor faulty; PCB faulty.  
Ed1 Wiring faulty between PCB and WD board; WD board faulty; PCB faulty. Cycle interrupted.
Ed2 Wiring faulty between PCB and WD thermostats; WD board faulty; PCB faulty. Cycle interrupted with door open.
Ed3 Wiring faulty between PCB and WD thermostats; WD board faulty; PCB faulty. Cycle interrupted with door open.
Ed4 Wiring faulty: WD board faulty; PCB faulty. Cycle interrupted with door open.
EF1 Drain tube blocked/kinked/too high; Drain filter dirty/blocked. Warning displayed at the end of cycle (specific LED).
EF2 Excessive detergent dosing; drain tube kinked/blocked; Drain filter dirty/blocked. Warning displayed after 5 attempts or by the specific LED.
EF3 Water leaks onto base frame; water control system defective. Machine drains and cycle stops
EF4 Tap closed, water pressure too low.  
EF5 Final spin phases skipped.  

Add comment


Security code
Refresh